Regulations Governing Compliance Approval for Controlled Telecommunications Radio-Frequency Devices｜第 6 條｜通訊｜Regulation｜In Force
第 二 章｜國家通訊傳播委員會｜v1.0
Last Amended: 2020-07-08
The examination report mentioned in these Regulations shall be issued by a testing body. Where the testing body as described in the preceding paragraph is unable to provide the test service for CTRFD or non-plug-and-play radio-frequency module（component）, the Applicant of compliance approval may submit the examination reports issued by test laboratory accredited by an accreditation body of a foreign country and the said report shall comply with the technical specifications for CTRFDs. Where the test laboratory accredited by an accreditation body of a foreign country as described in the preceding paragraph is unable to provide the test service for CTRFD or non-plug-and-play radio-frequency module（component）, the applicant may submit test reports provided by the manufacturer and the said report shall comply with the technical specifications for CTRFDs. The examination report as described in Paragraph 1 shall include the following: 1. Name and address of applicant; 2. Name and address of testing body; 3. Unique identification of examination report and the identification on each page of the report; 4. Name, brand and model number of device sample, external power supply, accessory, peripheral equipment, and test cable and test fixture; 5. 4x6” color photographs of device sample, external power supply and accessory with scale; the manufacturer and model number shall be clearly visible; the photographs shall show all six（6）sides of the device sample; the photographs mentioned in this subparagraph may be listed as an attachment to the examination report; 6. 4x6” color photographs of the interior of the device sample and circuit board with scale, showing at least two（2）sides; the main components on the circuit board shall be clearly identifiable; the photographs mentioned in this subparagraph may be listed as an attachment to the examination report; 7. Test connection diagram, test layout photographs and description; the device sample shall be connected to the external power supply, accessory and peripheral equipment; in the case where the test fixture and software are to be provided by the applicant in order to perform the test, the test fixture and the name and version of test software shall be specified. The test fixture shall be provided with 4×6” color photograph（s）with scale; 8. Settings of the device sample in normal use mode and test mode, including maximum transmission power, frequency, and bandwidth and modulation technique; however, for those for which the normal use mode is not available at the review, the normal use mode settings, such as maximum transmission power, frequency, and bandwidth and modulation technique, may be excluded. 9. Name, brand, model number, calibration date and expiration date of testing instrumentation; 10. Test items and standards as specified in relevant technical specifications; 11. General list of test results mentioned in Subparagraph 8 and the preceding subparagraph, verdict of test results and test data（including scanned images）; 12. Dates of acceptance and completion of test; 13. General antenna list for the device sample（including the type, brand, model number and maximum gain of the antenna and combination of power output with CTRFD or non-plug-and-play radio-frequency module（component））. The antenna shall be provided with 4×6” color photograph（s）with scale. The external power supply, accessory or peripheral that is not used in normal use mode, or the test cable, fixture or software that is not used in test mode may be excluded from the examination report. The test reports issued by a test laboratory accredited by an accreditation body of a foreign country in Paragraph 2 and manufacturer in Paragraph 3 shall include the following: 1. Name and address of Applicant; 2. Name and accreditation number of accreditation body, except for test report issued by the manufacturer; 3. Name and address of test laboratory or manufacturer; 4. Unique identification of examination report and the identification on each page of the report 5. Device name, brand and model number; 6. Color photographs of device sample; the manufacturer and model number shall be clearly visible; the photographs mentioned in this subparagraph may be listed as an attachment to the examination report; 7. Name, brand, model number, calibration date and expiration date of testing instrumentation; 8. Test items and standards as specified in relevant technical specifications; 9. Test data and verdict of test results; 10. Dates of acceptance and completion of test; The examination report shall be signed by relevant personnel of the testing body, whereas the test report shall be signed by the test laboratory or personnel of the manufacturer. For reapplications for review due to the change of non-RF hardware or non-RF function in a CTRFD or non-plug-and-play radio-frequency module（component）for which the approval certificate is issued, the test data and verdict of results of the original examination or test report may be cited. The citation mentioned in the preceding paragraph shall be valid only when the original testing body, test laboratory or manufacturer confirms the test data and verdict of results of the original examination or test report. Where the original testing body, test laboratory or manufacturer is unable to provide the test service, a testing body or test laboratory approved by the competent authority shall perform the test（s）and determine whether the test data and verdict of results of the original examination or test report are still valid. The examination or test report for reapplication for review in the previous two paragraphs shall include the unique identification of the original examination or test report as well as the contents specified in Paragraph 4 or 6.